Details of the slurry pump mechanical seal installation

Details of the slurry pump equipment sealing and installation:

First, the necessary prerequisite is: a professional inspection of the slurry pump seal in advance:

1, check the installation of the mechanical seal models, specifications are correct.

2, check the size of the slurry pump and mechanical seal installation site dimensions related to the accuracy and interrelationship with the technical requirements. Mainly in the following areas:

(1) Allowable radial runout of the shaft (or sleeve) where the mechanical seal is installed, surface finish of the shaft (or sleeve) and tolerance of outside diameter dimensions.

(2) seal cavity and gland positioning end face of the shaft (or sleeve) centerline vertical tolerance tolerance.

(3) The end of the shaft (or sleeve) on which the moving ring seal is mounted, and the chamfer and finish of the end structure of the housing bore for the mechanical seal.

(4) The axial displacement of the mechanical seal shaft when working.

(5) During the installation of the mechanical seal, it should be kept clean, and the sealing element should not be knocked by the tool to prevent damage and destruction.

Second, the correct operation of the installation of slurry pump:

1, the installation, moving, static ring surface should be coated with a layer of clean oil and turbine oil. Auxiliary seals (including moving ring seals and static ring seals) are also to be applied with a clean layer of engine oil or turbine oil before installation to ensure smooth installation.

2, the static ring seal set behind the static ring, into the sealed end cap, pay attention not to hurt the static end face, to ensure that the static end face and cover the centerline vertical, and pay attention to the back of the static ring to prevent trough to Alignment anti-sales, but can not touch.

3, the rotating part of the mechanical seal, relying on the spring seat on the two fixed screws and the shaft fixed, tighten the screws, to ensure the working length of the spring. The use of slurry pump mechanical seal Third, the use of the first start Note:

1, before starting the slurry pump, check the mechanical seal attached device, cooling lubrication system is perfect and smooth.

2, before starting the material line should be cleaned to prevent rust impurities into the sealed chamber.

3, hand drive coupling, check the shaft is easy to rotate, if the drive is heavy, need to check the installation dimensions are correct.

4, the normal drive, the need for static pressure test, check the mechanical seal face, seal ring and seal at the end of the sealing effect, if there is a problem, one by one to check and solve.

5, slurry pump start, should keep the sealed chamber filled with liquid or sealed medium, if a separate sealing system should be started, the cooling water system must also begin to flow.

6, before normal use, the first atmospheric pressure operation, observe the sealed parts of the temperature rise is normal, whether the phenomenon of leakage. If there is a slight leakage, you can run together for some time, so that the face fit more evenly, until the leakage gradually reduced to normal so far. Such as running 1-3 hours, the amount of leakage is still not reduced, you need to stop inspection.

7, under normal working conditions, step-up heating can be slow, respectively, and pay attention to the end of the temperature rise and leakage, such as all normal, that can be put into production.

Lithium Negative Cathode Material Crusher Equipment

I.Special equipment can be selected according to different raw materials, full automatic control, low energy consumption, no dust pollution in the processing process, clean and environmental protection, crushing precision in D50=5-17 micron between arbitrary adjustable. The particle shape is good and the curve is concentrated. It is widely used in crushing and grading of raw coke, raw coke, needle coke and calcined coke.

II.Full negative pressure design, high crushing and grading precision, particle size shaping, low energy consumption, small wear. Stone grinding granularity concentration, high classification accuracy, large output!


III.The average particle size of the material can reach 1-45 microns, and the particle size can be adjusted arbitrarily. It is an indispensable processing equipment for the battery material industry. Then the question comes, to what extent does the air pulverizer crush? It is related to the following factors: A. The initial fineness of the raw material, the airflow mill generally requires the feed to be below 50 mesh. B. It is related to the physical properties of the material, the fluidity of the material and the uniformity of the particles. Some materials flow...


1, the initial fineness of raw materials, air pulverizer generally requires the feed to be below 50 mesh.

2. It is related to the physical properties of the material, the fluidity of the material and the uniformity of the particles. Some materials have poor fluidity, many impurities, high solvent content, and there may be blockage in the production process. At this time, it is necessary to use special equipment to do it. Not all materials can be crushed with standard equipment to achieve the fineness of crushing.

3. It is related to the crushing pressure in the crushing process. Some equipment feed pressure is greater than the crushing pressure, and some equipment crush pressure is greater than the feeding pressure.

4, and feeding speed has a relationship, not all the material mobility is good, whether it is the use of screw feed or vibration feed, feeding process is a very important factor, some very fine material is difficult to feed, at this time you need to use a special personalized configuration to achieve the feeding effect.

5. It is related to the optimization degree of air mill. There are many manufacturers of air mill, but the fineness of the same material is different from that of different manufacturers, even if the fineness of different models of equipment from the same manufacturer is different. But as a rule of thumb, devices that are larger than the shredder plate produce better results than smaller ones.

6. The operation method is related to the proficiency of the operator. Some equipment needs to be started with small pressure operation first, and some directly operate in one step.

It can be seen from the above that the fineness of the airflow mill is not fixed, but adjustable. Because of this, it has become a favored processing equipment in various industries, which can meet the diverse needs of different users.


Lithium Cathode Material Crusher Equipment,Lithium Cathode Material Jet Mill,Lithium Cathode Material Pneumatic Pulverizer,Lithium Cathode Material Grinding Mill

Shandong Jing Xin Powder Equipment Technology Co., Ltd. , https://www.jxpowder.com