Inner Outer Wall Shot Blast Cleaning Machine with Abrasive Recovery System/Shot Blasting Machine

Steel Pipe Outer Wall Shot Blast Cleaning Machine with Abrasive Recovery System


Production description:
Use: This series cleaning machine (QGW) is applicable to various diameters steel tube suface cleaning, widely used in petrochemical engineering, steel, district heating, water and so on.

Advantage:
- For cleaning the outer wall of steel pipes and tubes.
- Floor mounted "BE" air wash separator for ease of observation and maintenance.
- The blast compartment and floor are consist of manganese plating to ensure longevity.
- Fully automatic design to provide high volume production and cost effective performance.


Specification of Steel pipe shot blasting machine:
Structural characteristice
This machine is a special reciprocating steel sand blasting machine, which consists of Blasting chamber, Blasting wheel assembly, Roller conveoyr, Abrasive recycling system (Screw conveyor, Elevator, Separator), Dust removal system, Electric control system, etc.

1. Blasting chamber
Shot blasting chamber shells adopt profile steel and steel plate welding structure, is a strong, sealing, spacious operation space for shot blasting of workpieces. Shot blasting chamber is made by room body shell, gate, wall around, lateral wall, roof after, guard board etc.

2. Blast wheel assembly
Blast wheel assembly is made up of blast wheel shell, motor, importing tube, leaf, impeller, directional set of pills, points wheel, block sand plate, guard board and other components, which leaves, guard board, etc all wear parts using 20% high-chromium cast iron.

3. Screw conveyor
The screw conveyor is a kind of abrasive horizontal conveying device, is an important part of the abrasive recycling system of the blasting machine.

4. Bucket elevator
The bucket elevator consists of speed reducer, upper and lower rolling barrel, transmission rubber belt, bucket elevator, enclosure and tightening device, etc.

5. Separator
This machine adopts advanced Model BE full shutter type separator. The separator is mainly composed of airwash area, barrel sift, conveying screw, abrasive hopper, manual abrasive controlling valve.

6. Dust removal system
This machine adopts Cartridge or Bag type dust collector, is exhausted air produced during working. The dedusting efficiency is up to 99.6%, powder density is less than 100mg/m3,much stricter than the national standard.

7. Electric control system
Set shot ball circulatory failure alarm function, if any parts of the system fails, the above components automatically stop running, to prevent the shot ball stuck and burning power device.

Company capacity:
Trade Information:
MOQ: 1set.
Settlement Currency: USD, RMB, EUR.
Trade mode: FOB, CIP, CFR, CIF, DDU, DDP.
Payment term: 30% deposit by T/T, the balance paid before delivery or L/C at sight.
Delivery time: Within 15-40 days according to different type machine.

After-sale service:
1. Installation and commissioning issue: We will send 1-2 technicians to assist with machine installation and commissioning, customer pays for their tickets, hotel and diet. Customer need arrange 3-4 skilled worker and prepare insallation machinery and tools.
2. Warranty time:12 months from date of commissioning completion, but no more than 18 months from date of delivery.
3. Supply full english documents: including general installation drawings, pit design drawings, manual book, electric wiring diagram, electric manual book and maintenance book, etc.
4. Exported experience : Many countries, such as The USA, Russia, UK, Ukraine, Australia, Malaysia, UAE, Egypt, Mexico, Brasil, etc.
5. Our shot blasting spare parts are high quality with High Chrome Castings, 40Cr, ZGMn13,  etc.

Notice:
According to your requirements, the most suitable machines will be designed for your workpieces, please indicate the following details.
1. What kind of workpiece will you clean?
2. The workpiece size, length, width, height and weight of maximum workpiece.
3. How many workpieces do you want to clean per day?
Based on this detail information, the detailed technical proposals will be sent to you for reference.

Any question pls feel free to contact with me and welcome to visit our factory! Steel Pipe Outer Wall Shot Blast Cleaning Machine with Abrasive Recovery System


Production description:
Use: This series cleaning machine (QGW) is applicable to various diameters steel tube suface cleaning, widely used in petrochemical engineering, steel, district heating, water and so on.

Advantage:
- For cleaning the outer wall of steel pipes and tubes.
- Floor mounted "BE" air wash separator for ease of observation and maintenance.
- The blast compartment and floor are consist of manganese plating to ensure longevity.
- Fully automatic design to provide high volume production and cost effective performance.


Specification of Steel pipe shot blasting machine:
Structural characteristice
This machine is a special reciprocating steel sand blasting machine, which consists of Blasting chamber, Blasting wheel assembly, Roller conveoyr, Abrasive recycling system (Screw conveyor, Elevator, Separator), Dust removal system, Electric control system, etc.

1. Blasting chamber
Shot blasting chamber shells adopt profile steel and steel plate welding structure, is a strong, sealing, spacious operation space for shot blasting of workpieces. Shot blasting chamber is made by room body shell, gate, wall around, lateral wall, roof after, guard board etc.

2. Blast wheel assembly
Blast wheel assembly is made up of blast wheel shell, motor, importing tube, leaf, impeller, directional set of pills, points wheel, block sand plate, guard board and other components, which leaves, guard board, etc all wear parts using 20% high-chromium cast iron.

3. Screw conveyor
The screw conveyor is a kind of abrasive horizontal conveying device, is an important part of the abrasive recycling system of the blasting machine.

4. Bucket elevator
The bucket elevator consists of speed reducer, upper and lower rolling barrel, transmission rubber belt, bucket elevator, enclosure and tightening device, etc.

5. Separator
This machine adopts advanced Model BE full shutter type separator. The separator is mainly composed of airwash area, barrel sift, conveying screw, abrasive hopper, manual abrasive controlling valve.

6. Dust removal system
This machine adopts Cartridge or Bag type dust collector, is exhausted air produced during working. The dedusting efficiency is up to 99.6%, powder density is less than 100mg/m3,much stricter than the national standard.

7. Electric control system
Set shot ball circulatory failure alarm function, if any parts of the system fails, the above components automatically stop running, to prevent the shot ball stuck and burning power device.

Company capacity:
Trade Information:
MOQ: 1set.
Settlement Currency: USD, RMB, EUR.
Trade mode: FOB, CIP, CFR, CIF, DDU, DDP.
Payment term: 30% deposit by T/T, the balance paid before delivery or L/C at sight.
Delivery time: Within 15-40 days according to different type machine.

After-sale service:
1. Installation and commissioning issue: We will send 1-2 technicians to assist with machine installation and commissioning, customer pays for their tickets, hotel and diet. Customer need arrange 3-4 skilled worker and prepare insallation machinery and tools.
2. Warranty time:12 months from date of commissioning completion, but no more than 18 months from date of delivery.
3. Supply full english documents: including general installation drawings, pit design drawings, manual book, electric wiring diagram, electric manual book and maintenance book, etc.
4. Exported experience : Many countries, such as The USA, Russia, UK, Ukraine, Australia, Malaysia, UAE, Egypt, Mexico, Brasil, etc.
5. Our shot blasting spare parts are high quality with High Chrome Castings, 40Cr, ZGMn13,  etc.

Notice:
According to your requirements, the most suitable machines will be designed for your workpieces, please indicate the following details.
1. What kind of workpiece will you clean?
2. The workpiece size, length, width, height and weight of maximum workpiece.
3. How many workpieces do you want to clean per day?
Based on this detail information, the detailed technical proposals will be sent to you for reference.

Any question pls feel free to contact with me and welcome to visit our factory!

We manufacture Lovol Diesel Generator with good price and high quality.

Open Type,

Silent Type.

Mobile Wheels trailer tyle.

Automatic Type.

2 years warranty.

10 Days delivery.

Tianjin Lovol Engines Co., Ltd. Which is the prior Perkins(Tianjin) Co.,Ltd , Sino-British Joint Venture Perkins(Tianjin) Co., Ltd, founded in 1997, occupied the land of 88,000m2, workshop occupied 26,000m2, seven modernized production lines have been purchased from the UK, the USA, Germany, France, etc., and the production base for 60,000 sets of diesel engines has been established.

Lovol Diesel Generator

Lovol Engine Generator, Lovol Engine Generator Set, Lovol Diesel Portable Generator, Lovol Diesel Power Generator

Weifang Huatian Diesel Engine Co., Ltd , https://www.higenset.com